Kmc-controls CTE-5201-16 Manual do Utilizador descarregar pdf

CTE-5201 1 Installation and Operation Guide

Mounting the Thermostat

1. Ifthethermostatis

lockedonthebackplate,

turnthetwohexscrews

(inthetwo outermost

holes)inthebackplate

CLOCKWISEuntilthey(just)clearthecover.

Swingthethermostatupandawayfromthe

backplatetoremoveit.

CAUTION

To prevent damage to the board, do not insert

a screwdriver into any holes other than the two

outermost holes. To prevent mounting screw heads

Installation and Operation Guide

Electronic Room Thermostat (Modular)

CTE-5201

Mounting

Rough-in Preparation

For optimum temperature sensor performance, the

thermostat must be mounted on an interior wall

and away from heat sources, sunlight, windows,

air vents, and air circulation obstructions (e.g.,

curtains, furniture).

Completerough-inwiringpriortoinstallation:

• Routethecablefromthethermostatlocationto

theactuatortowhichitwillconnect.SeeWiring

on page 2.

•

Ifneeded,installtheHMO-1161mounting

backplate.SeeAdditional Information on page 4.

from touching the circuit board in the thermostat, use

only the mounting screws supplied by KMC Controls.

Using other screws may damage the thermostat. Do

not turn screws in farther than necessary to remove

the cover.

2. Routethecablethroughthebackplate.

3. Withthehexscrewstowardthe

oor,fastenthebackplatetothe

outletboxwiththesuppliedscrews.

(Thebackplatemountsdirectlyon

vertical2x4inchboxes,butre-

quiresanHMO-1161wallmounting

plateforhorizontalor4x4boxes.)

4. Insertthemodularendofthecable

intothejackofthethermostat.

5. Placethetopofthethermostatoverthetopof

themountingbaseandswingitdownoverthe

hexscrewbrackets.Becarefulnottopinchthe

wiring.

6.

Backthehexscrewsoutofthebackplatebrackets

(counterclockwise) untiltheyengagethether-

mostatandholditinplace.

E F

RJ-12

Modular

Connector

Pin 6

Pin 1

Mounting 1

Rough-in Preparation 1

Mounting the Thermostat 1

Wiring 2

Modular to Modular (HSO-22xx Cable) 2

Modular to Leads (HSO-5012 Cable) 2

Operation 3

Turn On Backlight 3

Change Setpoint 3

Start Unoccupied Mode 3

Toggle Between °F and °C 3

Conﬁguration 3

Changing Defaults 3

MAX 3

MIN 3

F/C 3

UNOCC 3

PROP 4

INT 4

Calibration (Temperature Offset) 4

Maintenance 4

Additional Information 4

Pin 1 and 6 Pin 2 and 5 Pin 3 Pin 4

N/C Common Supply

(14–19VDC)

Output

(2–10VDC)*

*0VDCduringUnoccupiedOmodewhentemperaturestays

above50°F

3.25

in.

83

5.16

in.

116

0.88

in.

22

0.38

in.

10

2.58

in.

66

3.25

in.

83

1 2 3 4

Resumo do Conteúdo

Página 1 - CAUTION

CTE-5201 1 Installation and Operation GuideMounting the Thermostat1. Ifthethermostatislockedonthebackplate,turnthetwohexscrews(in

Página 2 - 3/8"

CTE-5201 2 Installation and Operation GuideWiringModular to Modular (HSO-22xx Cable)UseHSO-22xxcablestoconnectthether-mostattoMEP-4x42a

Página 3 - Operation

CTE-5201 3 Installation and Operation GuideConﬁgurationOperationChanging DefaultsThefactorydefaultseingsare:• Setpoint(Default):70F•

Página 4 - Additional Information

CTE-5201 4 Installation and Operation GuideMaintenanceRemovedustasnecessaryfromholesintopandboom.Cleanthedisplaywithso,dampclo

Comentários a estes Manuais

Sem comentários

Kmc-controls CTE-5201-16 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Sensores Kmc-controls CTE-5201-16. KMC Controls CTE-5201-16 User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Kmc-controls CTE-5201-16